Ford Econoline / E-Series Van – Electric Automatic Powerstepz Running Boards Installation instructions

BigDickOffroad.com > Ford Econoline / E-Series Van – Electric Automatic Powerstepz Running Boards Installation instructions

Installation Instructions for  Ford Econoline Electric Powerstepz Running Boards — 2pc Kit

Fits Ford E-Series Vans (1992–2025)
Brand: HF USA 

Econoline Electric Powerstepz running boards 2pc Kit for Ford Van 1992-1996 | 1997-2025

IMPORTANT: READ BEFORE INSTALLING

  1. Know your ride. These instructions apply to Econoline (E-Series) vans, 1992–2025. Check fitment before you start.

  2. Prep the work area. Keep it clean, dry, and safe. Park on level ground.

  3. Battery first. Disconnect the negative terminal before installation.

  4. Mind the heat. Don’t route wires near exhaust, engine components, or hot zones.

  5. Keep it dry. The control module isn’t waterproof. Mount in a dry area — under the dash or behind interior trim.

  6. Secure everything. Use zip ties, fasteners, and tape provided to keep wiring tight and protected.

  7. Do not shortcut. Always test before finalizing your wiring and trim reinstallation.

WHAT’S IN THE BOX

Main Components (Qty):

  • Electric Running Boards (2)

  • Front Mounting Brackets (2)

  • Rear Mounting Brackets (2)

  • Control Module (ECU) (1)

  • U-Bolts & T-Bolts (10 total)

  • Bolts, Washers, Spring Washers (full hardware kit)

  • Waterproof Rubber Tape

  • Zip Ties (25)

  • Plastic Spacer Blocks

  • Wire Harnesses (L/R motor harness, magnetic sensor harness, extension cables)

  • Magnetic Sensors (4)

  • OBD Pickup Module

REQUIRED TOOLS

  • Socket Wrench Set

  • Open-End Wrench

  • Phillips & Flathead Screwdrivers

  • Hex Wrenches

  • Knife/Scissors

  • Wire Stripper/Cutter

  • Electrical Tape

  • Drill (optional, if mounting points aren’t pre-drilled)

INSTALLATION PROCESS

1. MOUNTING THE STEPS

  1. Test-fit brackets and running boards to identify L/R, front/rear positions.

  2. Install front and rear brackets to frame rails using U-bolts and included washers.

  3. Align steps to brackets using T-bolts and socket head screws. Tighten but don’t over-torque.

  4. Ensure steps clear the door and body when deploying.

2. MOTOR & WIRING HARNESS

  1. Route motor wiring harness along the underbody, avoiding heat/exhaust areas.

  2. Connect left/right motor plugs to running board actuators.

  3. Run the harness into the cabin (through grommet or firewall).

  4. Secure excess wiring with zip ties. Use rubber tape to insulate exposed connectors.

3. ECU & POWER

  1. Mount the ECU under the dash or in another dry location.

  2. Connect power (red) to a 12V source with inline fuse (included).

  3. Connect ground (black) to a solid chassis ground.

  4. Plug the OBD module into your OBD port (under dash, driver side).

4. MAGNETIC SENSOR SYSTEM

  1. Pull weather seal near B-pillars and clean surface.

  2. Stick magnetic sensors along the door frame.

  3. Apply inked foam to the sensors and gently close the doors to mark where magnets go.

  4. Mount magnets inside door skin aligned to ink marks.

    • Do NOT place magnets over trim or edge lines.

    • Seal with 704B silicone or similar adhesive sealant.

  5. Once dry, remove the foam and secure all sensor wiring.

5. FINAL CHECKS

  • Confirm all connections are tight and clean.

  • Test door open/close – steps should extend and retract automatically.

  • Tidy up all wiring. Secure with zip ties and tape.

  • Reinstall any trim or panels removed during install.

  • Done right? Time to flex.

WARRANTY NOTICE

This kit includes a 12-month limited warranty covering manufacturing defects.
Misuse, water damage to ECU, or poor installation voids the warranty.

Add to cart